*Please note, shipping on this item is completely FREE. We ship to you and also include a Free return label within the box, so simply tape the label on the box after SAFELY repacking the hardware and drop it off at the post office :)
Factory ECU, Key, Immobilizer Re-Programming to Vehicle
( For Hondata Compatibility, Etc
Up to Year 2010' Vehicles)
Please be sure to read over the ENTIRE DESCRIPTION AND REQUIREMENTS FOR THIS LISTING
Pricing, Refund, Fee
Please note, due to the equipment being utilized, we require and upfront equipment charge, similar to a core fee. Once the service have been performed and our equipment is returned back to us intact, we will then issue the credit back to the card on file. There is also a $40 per day late fee associated to this service and return of equipment.
Exceptions do apply, but the late fee is based off the time frame (24hrs) we provide for this service (full description below in the product "Requirements" section. If the time frame is not met, the late fee of $40 pr day is applied and pulled from the upfront Equipment Charge Credit.
Description/How it Works -
As many know, certain tuning software require the appropriate ECU's to be ran in order to support the software and ultimately be able to tune your vehicle....or the stock ecu simply goes bad and a new one is needed. In doing so, when a stock ECU is swapped out it must be re-programmed to that new vehicle, as will the Key and Immobilizer, or the car wont run. In the past many customer will take their vehicle to the dealer after everything is wired in (if they can find a dealer willing to, as some refuse with the "Race Only" software) and then swap the ECU and have them re-program it. It's time consuming, very little support offered if issue's do arise and worse is the HIGH COST (sometime as much as $450)..... WELL THOSE DAYS ARE OVER. Our reprogramming service's allow you to do everything from your garage or home! If you meet the requirement's listed below in our "Requirement" list, then you make the purchase, we ship our laptop and hardware to you, you connect everything together and plug it in to the OBD2 connector slot of the vehicle. From there WiFi is required as we remotely tap into the laptop and take over. Your physical services will be required, as certain procedures require cycling of the key on/off and other various processes.
- Perfect for OEM fixes too -
Fried OEM ECU
Lost Key
Unprogrammed Immobilizer
Requirements
(must read over ALL of these)
1.) You must have ALL of the wiring, hardware, ECU etc. already purchased and installed.
This service is meant to be the end procedure in setting up you new ECU, without everything in place this service is useless. This is very important as there is a 24hr time limit on this item from the point of delivery to customer and return shipping back to HalferLand Performance (return tracking provided to us). That means when the unit arrives, your clock starts. This means DO NOT PURCHASE this service until you 100% have everything wired up and ready for the ECU to be programmed to the new vehicle, key and immobilizer. Each day over the time limit is a $40 fee ($40 per day). This is in place to keep it fair and allow each customer their time, without one keeping the unit for weeks.
2.) Purchasing for Hondata Compatibility -
As stressed in #1 , it's required you have all wiring, hardware, ECU's, and tuning software already hooked up. In the case's of vehicles such as 03-07 Accord MT and 04-06 TL MT, Hondata requires the adapter harness and CAN adapter to be installed. Without doing so our service will not work properly and you'll be stuck purchasing this service another time. AGAIN, ALL WIRING/HARDWARE, ETC MUST BE INSTALLED PRIOR TO PURCHASING THIS SERVICE.
*If you're using our service to add Hondata Flashpro to your 03-07 Accord V6 MT or 04-06 TL V6 MT, and are using the 07-08 TL AUTO ECU
1.) You must first register your Flashpro unit and create an account with Hondata, and register the unit as "OUTSIDE THE U.S." or we will be locked out
2.) You must convert/Flash the ECU using the Flashpro unit from Auto to MT (selecting the proper ECU in the software. This is done by being hooked up to the OBD2 in the car). The Ecu does not need to be synced to the car to do this. This step is very important or the ECU will not work, as it's an AUTO ECU and needs to be Flashed to MT.
If you are unsure whatsoever about this process, PLEASE CONTACT US BEFORE TOUCHING YOUR HODATA UNIT and first download the Hondata FlashPro editing software from their website onto your computer, as the software will be needed. We can also do this for you remotely once you receive the hardware from us. It's important this is done correctly or our hardware will be locked out and will not work.
3.) MUST HAVE WIFI / INTERNET ACCESS AVAILABLE AT THE VEHICLE LOCATION
Our computer requires internet access at the time the service is being performed and this service requires that you have wifi available (GOOD WIFI, NOT MC.DONALD PARKING LOT WIFI). If you do not have internet access or cannot get it, please do not purchase this service. All sales are final for this service, no refunds will be issued if we attempt to perform the service and you have no wifi. Thank you