HalferLand Performance's
MAX Flow 79/81mm Billet Anodized Drive By Wire Throttle body
&
4" High Velocity Carbon Fiber Cold Air Intake - KIT/BUNDLE
Vehicle Fitments
- 03-07' Accord V6 (AT & MT Trans)
- 04-08' Acura 3.2 & 3.5 TL / TL Type S (AT & MT Trans)
- 05-08' Acura RL (AT Trans)
AS ALWAYS - Backed by our Industry Leading (and only we're aware of) HLP 1year Guarantee/Warranty against any defects or failure!
~~ FEATURES ~~
HLP's J-Series 4" High Velocity Dry Carbon Fiber Cold Air Intake
- Best Flowing and HP gaining J-Series 4" Cold Air Intake on the market
- Average HP gains of 10-14hp seen in re-tuned vehicles (vs others 4" on the market around 6-8hp)
- NO TUNING REQUIRED. Can be ran with the stock/oem ecu and tune (Tuning is suggested to see full potential)
- The lightest in weight, Honda/Acura J-Series Cold Air Intake on the market, weighing in at just 13oz....not even 1 full pound !!!
- High Velocity Reduction and smooth transitions allow for the best flowing 4" Cold Air Intake you can buy for the J-Series Platform
- Dry Carbon Fiber is far superior & does not retain as much heat as Aluminum or Steel, leaving you with the coolest operating 4" CAI you can get
- Superior Dry Molded Carbon Fiber in a Billet Press vs "Wet Molded" painted on/together carbon. Dry leaves you with the lightest and strongest carbon fibers possible (Aerospace and NASA quality)
- The smooth reduction (NOT Choke, BIG DIFFERENCE) greatly increase air velocity through the entire intake and mostly around the tightest radius in the intake pipe. It is not just a pipe inside a pipe as other very popular 4" Aluminum intakes on the market (ironically, priced around the same as our...Carbon Fiber vs 3" aluminum pipe welded inside a 4" aluminum pipe) - See listing images.
- Available 9" Black or 10" Red High Flow Multi-Inlet Dry Intake Filter. Great Flow and zero maintenance (performance may vary if you supply your own filters)
HLP's J-Series 4" High Velocity Dry Carbon Fiber Cold Air Intake
- CNC machined from a single block of robust 6061 Billet Aluminum
- LARGEST and best gaining Drive By Wire J-Series TB on the market
- Comes standard with black anodizing to harden and help with intake temps
- 100% Plug N Play for ALL J30, J32 and J35 Intake manifold (NO adapters needed)
- Average HP Gains of 8-15hp seen in Re-Tuned vehicles. That's compared to averages gains with the J37 ZDX of 5-7hp.
- NO TUNING NEEDED. Can be ran on the stock/oem ecu and tune (Tuning is suggested to see full potential)
~~ THROTTLE BODY SPEC'S COMPARISON ~~
~ HLP Billet Throttle Body Specs ~
Stock = 79mm Inlet x 72mm Plate x 72mm Outlet
PNP = 81 inlet x 72mm Plate x 72mm Outlet (increased air velocity even further)
Compatible Intake Manifolds - ALL Drive By Wire J30, J32, J35
~ ZDX / MDX SPEC'S ~
78mm Inlet x 68mm plate x 70mm Outlet
Compatible Intake Manifolds - J37 Only (unless you purchase an additional $150 adapter)
PRODUCT DESCRIPTION
Well, we're at it again! We are proud to bring you our new HLP' MAX FLOW J-Series Billet Throttle Body & 4" Carbon Fiber Cold Air Intake Kits! Separately these two parts have hands down been shown to out gain all other throttle bodies and CAI's currently on the market. Our HLP 79/81mm x 72mm Billet Throttle Body is the LARGEST and best flowing DBW J-SERIES TB available for these engines, even out gaining the smaller 78mm/70mm J37/ZDX Throttle Body by 40% or MORE. To top that, our HLP 79/81mm Billet throttle body also bolts directly to ALL Drive By Wire J30, J32 and J35 Manifolds, where the J37/ZDX requires you to purchase an expensive( and NOT the best) J37 Manifold (touch on that below) or you need to purchase an adapter plate just to run it. We won't get too far into it, but there's a reason we do not offer the J37 Manifold or Holley (designed for LS engines, not J-Series), simply put the J35 Mag IM has been shown to be the best overall manifold available, showing great mid and top end power, where the J37 shows minimal torque gains below 4k rpm (guess it's good if you want to tow a trailer....that's 5wtq down low should really help ??) and the Holley in some cases has LOST POWER on NA setups, where some gains may be seen if forced Induction but we would still take the J35 Mag over it, even in stock form just for the cooler operating temps of the magnesium (then add our IAT reducing ceramic enamel finish and its the coolest Operating IM you can get).
Then our HLP 4" High Velocity Carbon Fiber intake not only sees great gains over the AEM 4" V2 (pipe inside a pipe, zero thought on transitions) it also maximizes velocity through the main turn/radius, while being Carbon Fiber retains very little heat, even compared to aluminum, again being the coolest Operating and best flowing CAI you can get for our beloved J-Series platform!
~~ KIT PLUG N PLAT FITMENTS ~~~
03-07' Honda Accord V6 (Auto & MT)
04-08' Acura TL 3.2 & 3.5 (Auto & MT)
05-09 Acura TL 3.5 (Auto)
- SOLD SEPARATELY PRICE - $1,021.90
- HLP MAX FLOW KIT/BUNDLE - $935.95
* $85+ SAVINGS *
NOTICE FOR APPLICATION AND USE
This product is manufactured for race use only, and is sold for installation on vehicles designed solely for competition purposes only. It is the installers and/or user of this product responsibility to ensure that it is used in compliance with all applicable laws and regulations according to their State or Region.
Once this product is installed, the vehicle may never be used, or registered or licensed for use, on a public highway or road. If you install this product on your vehicle and use the vehicle on a public highway or road, you will violate the clean air act and may be subject to personal civil or criminal liability, including fines.
* RETURNS & ORDER CANCELING POLICY*
- ALL ORDERS ARE SUBJECTED TO OUR (1) MONTH (28 DAYS) RETURN POLICY (THIS EXCLUDES ANY PORT AND POLISH PARTS, PNP PART RETURNS/CANCELLING IS BELOW). WE OFFER A NO HASSLE RETURN POLICY ON ANY PARTS WITHIN THE FIRST (28) DAYS OF YOUR PURCHASE. ALL PARTS MUST BE RETURNED IN THEIR ORIGINAL CONDITION, PACKAGING AND NEVER INSTALLED. A FULL INSPECTION WILL BE PERFORMED UPON RECEIVING THE ORDER/PARTS BACK TO US AND IF DETERMINED THE PART WAS INSTALLED OR MODIFIED/DAMAGED THE RETURN WILL BE DENIED. IF WE WERE AT FAULT OR AN ERROR OCCURED ON OUR END, WE WILL SUPPLY A FREE RETURN SHIPPING LABEL. IF THE ERROR WAS ON THE CUSTOMER SIDE OR THEY SIMPLY NO LONGER WANT THE PRODUCT WITHIN THAT FIRST 28 DAY POLICY, THEY CUSTOMER IS RESPONSBILE FOR THE RETURN SHIPPING COST, SETUP AND EXECUTION.
ALL REFUNDS AND RETURNS ARE SUBJECT TO A 3.5% CREDIT CARD TRANSACTION FEE. THIS IS DUE TO THE INITAL ORDER TRANSACTION FEE WE WERE CHARGED FOR YOUR ORDER, PLUS THE ADDITONAL REFUND TRANSACTION. THOUGH THERE ARE TWO TRANSACTION FEE'S CHARGED TO US, WE ARE ONLY CHARGING YOU FOR THE REFUND FEE.
- ANY PART RETURNED AFTER THE (28) DAY RETURN POLICY WILL BE SUBJECTED TO AN ADDITONAL 3.5% RESTOCKING FEE, BRINGING THE TOTAL FEE TO 7%.
- FOR TUNING ORDERS, NO RETURNS ARE ACCEPTED UNLESS NO TUNING OR REVISIONS HAVE BEEN STARTED. AFTER OUR FIRST REVISION/TUNE IS SENT TO OUR CUSTOMER VIA EMAIL, NO REFUNDS WILL BE ALLOWED OR AUTHORIZED. THIS APPLIES FOR BOTH SINGLE SESSION (TUNE TILL RIGHT) AND LIFETIME TUNES.
- There are no returns accepted for any Port and Polish parts, due to the parts being modified and unable to be returned to their stock/original condition. There is no exception to this policy...EVER.
- If the customer selected to have HalferLand Performance source/provide a core part(s) and chooses to cancel their order prior to shipping or starting the modifications/porting, a 20% part cost restocking/sourcing fee will be assessed from the credit/return. Example, the core part provided cost $100, a 20% Restock/Sourcing fee of $20 will be deducted from the credit of the order. This is due to our cost to source, purchase, clean the part and now the order being cancelled, we now are forced to sit on the part with direct order being associated with it or that we can use it for.
- Order Cancelling may be done prior to the start of any modification or work and before shipping. If the parts modifications has already been begun or the parts has shipped, then the order cannot be canceled and will be filled/finished accordingly. If its a non PnP part and the order ships, the customer is responsible for returning the part/order using their preferred carrier. Our (28) Day Return Policy guidelines remain, parts must be returned in original packaging, never installed, modified or damaged.
