CUSTOMER SUPPLIED PARTS -
I have the rear main seal - Will need it shipped to us
front main seal, - Will need it shipped to us
water pump and gasket - Will need it shipped to us
2 oil orifice with orings, - Not sure what you mean by this...Will need it shipped to us
oil pump, - Will need it shipped to us
oil pipe for oilpump with orings, - Will need it shipped to us
oil strainer with oring, - Will need it shipped to us
timing tensioner, - You install since the heads are required for this task
timing idler, You install since the heads are required for this task
unorthadox crank pulley, You install since the heads are required for this task
crank pulley bolt, You install since the heads are required for this task
unorthadox tensioner pulley, You install since the heads are required for this task
crank sensor, - You install since the heads are required for this task
knock sensor and spool valve filter. You install since the heads are required for this task
- J35Z3 Block - Pre-Installed CSS Support + Services below - $1,965.95 Free Shipping
Block will be Resurfaced, Bored/Honed for 89.25mm pistons - NO Compression rings unless you are okay with 5-6week to get them installed + additional $585 on top of total
- J35Z3/Z6 Crankshaft - Pulled directly from this engine that had 88k miles on it. PERFECT condition - FREE at cost of CSS Block
- HLP J35 1300HP H-Beam Rods - $705.95
- Wiseco Ductile Piston ring set
- HLP/Felpro G3 Performance Head gasket - $79.95
- HLP Thick Horned Piston Wrist Pins Set of 6 - $59.95
- Wiseco 89.25 +.25mm Forged Domed Pistons 10.6:1 compression - We suggest these to fine tune the piston to wall clearances. Being only .25mm oversized also allows for future rebuilds, where the .50mm over piston are maxing out the amount you can machine the cylinders. - $969.95 (currently on sale)
- King Racing XP Race Coated .001 HX Main Bearings - .001" extra clearance for more load - $99.95
- King Racing XP Race Coated .001 HX Rod Bearings - same as the mains - $139.90
- King Thrust bearings -$24.95
- HLP Piston Oil Squirter Plug Bolt Kit - To bump oil pressure for high loads - $23.95
ASSEMBLED CSS J35Z6 SHORT BLOCK - $5,595.40 - $250 labor/part discount for you providing some items + 6% Tax =
$5,666.12 FREE SHIPPING - 50% deposit due to start
- Includes all of the parts from Quote #1 (above) + the below assembly services and machining. This Block will be ready for cylinder head installation, timing belt, etc.
Accessory pulleys, timing belt tensioner, timing belt (which we offer the Gate Blue RPM belt if you want add that in at cost) , timing covers, etc etc., so all the small snout side accessory parts will be swapped over by you and from your current engine, being the heads are needed for those services to be completed.
Block Tear Down/Disassemble |
Block Assembly /Rebuild - ALL PARTS REMOVED ARE FULLY SONIC AND CHEM BATHED CLEANED |
Main Journal Bearings (Blue Printed, Dial Bored, Cleaned & Installed) |
Rod Bearings (BluePrinted, Dial Bored and Cleaned, Installed) |
Diamond CNC Cylinder Hone / Bore for 89.25mm Wiseco Pistons |
All new seals/ Gaskets + Head Gasket only Long Block builds (Front, Rear, Vtec Solenoid,, Water Pump SEAL INCLUDED) |
Block Decking / Head Gasket |
Piston & Piston Ring Gapping - New Rings + Install |
New Water Pump + seal and Accessory pulleys |
