OilAdapter - TracTuff Vtec Solenoid Oil Filter Relocation Adapter *ALL MODELS* (Adapter to Engine Block ONLY) - (FREE SHIPPING)

review
5
0
5
Your Price: $199.95
ITEM IS IN STOCK, READY TO SHIP
Free Shipping.
Part Number:Trac-Oil-HP

Choose Options

Add -10 AN ORB Fittings x2 (Includes both needed to come out and In to the adpater)
Honda J-Series  TracTuff
 Solenoid Oil Filter Relocation Adapter + Pressure Switch O-Ring

- Fits ALL Model J-Series Engine (Read Installation)-


Product Description
We are very proud to announce our new product stocking with the TracTuff' Oil Filer Relocation Kit, offering which is hands down the best Oil Filter Relocation kit on the market. If you have every attempted a typical install of the common Oil Filter Relocation kits on the market you would have found the same obstacles and flaws we did. First, there's simply no room for anything additional in the front passenger fender/tire well. As most people, we attempted to route lines around the lower control arm, around subframes, under control arms, past the crank pulley...none of those attempts were good "Safe"" locations or routing....there simply wasn't enough room. We ended up finding the lines either ran to low, ran into another parts or were dangerously close to other parts and the road.....Well that is NO MORE!

With this TracTuff relocation kit the adapter bolts straight onto the block in place of the stock Vtec Solinoid. What that does is bring the entire unit and the lines higher up, closer into the actual engine bay allowing for more room and free range to route oil lines safely and creates a small profile overall which takes up much less room. On top of that the piece is absolutely beautiful, being fully machined from a solid 6061 Block of Billet!

Please note, this listing is ONLY for the Vtec Solenoid adapter block, you will still need to purchase the actual Oil Filter Relocation housing which the filter screws onto (in that case the traditional kits like you see on Ebay can be used, as it's relocated and not in any danger of be damaged or too close to moving parts). So in sum, this listing is only for the part that bolts to the engine block, from there it has the -10AN oil lines coming out of it, over to the oil filter housing you install elsewhere remotely. 

You may also add our -10 ORB fittings from the drop down menu next to the pricing, as they can be tough to find on the market sometimes. We have found the best option is a straight fittings out of the relocation block, and then either 45* or 90* -10AN swivel fittings off of them into your -10 Oil lines, which then route to the oil filter housing relocation adapter. 

The adpater will include only the Oil Pressure Switch O-Ring, but no other gasket is offered. It would be in the customer best interest to purchase the main gasket at a minimum (Vtec Spool Valve Main gasket and screen as they usually compress over time and the screen clogs). 



Installation

1.) The Billet Adapter Installs in the place of the stock OEM Vtec Solenoid. Take the Solenoid off, swap all sensors over, swap the Vtec Plunger AND SPRING over and then install the new Billet Adapter. It's that easy

2.) The area of installation can be tight and we found there's much more room if you remove the front passenger axle for installation. 

3.)  It's also best to install all fittings tightly onto the adapter block before installing it, as again there's limited access in that area of the engine bay/wheel well (hence the need to this adapter block)

4.)  GEN 2 AND GEN 3 ENGINES (We list all engine Generations on our main website Q&A forum (https://hondajseriesengine.com/answers/page/2/?widgetCacheId=7f2be8d4bf7de1a6dd49c303601e22bc)
 It must also be noted the fitment between the -10ORB fittings coming out of the adapter block and the crank pulley (whether the fittings are purchased from us or 3rd party) will be very tight tolerances, so it's best to have your accessory belt Pre-installed on the crank pulley before attempting the install.

5.) You will need (2) -10 ORB fittings (average cost online is $29.95...OUR PRICE IS $19.95 so it's a good idea to add this option to your order!)  to be installed on the kit (as shown in the product photos). From there you may source whatever -10 swivel fitting that suites your needs (we found 45* or 90* works best). We do offer the -10AN ORB fittings on the drop down menu near the pricing and will include both (x2) if you choose to include them with your purchase.

6.) Sensors, Gaskets and Fittings are NOT included (only the Pressure Sensor O-Ring and the Adapter Block). However, again we do offer the option to purchase the -10 ORB fittings from the drop down menu located next to the pricing. For gaskets, we found Rockauto.com to have the best quality and prices without having to search too hard on the web.

5 Stars
Perfect
This was exactly what I needed. It solved an issue I was battling with for literally months. The product is high quality, customer service and shipping was also perfect. Thanks
Did you find this helpful? 
Reviewed by:  from Detroit . on 4/12/2020
5
5 Stars
Works great
Hands down this is a problem solver. A++
Did you find this helpful? 
Reviewed by:  from West Port. on 5/31/2020
5

Accessories

E Tuning - Remote / Email / Local Dyno Tuning Service-  Hondata or Ktuner Tuning (Tuning Only)
Average Rating(11)
$349.99
ITEM IS IN STOCK, LETS PULL SOME EXTRA POWER OUT OF THAT J-SERIES MOTOR!! ;) Free Shipping.